Skip to content
← Calculators

3D frame — FEM

Linear static analysis of a small space frame by the finite element method (FEM): nodal displacements, reactions, member end forces and N, Vy, Vz, Mt, My and Mz diagrams with extremes. The model is entered numerically and calculated with the Calculate button.

3D frame — FEM

First-order linear statics · spatial Euler–Bernoulli beam · ≤ 10 nodes, ≤ 5 members

View

Fixed axonometric view. The arrow on a member points from node i to node j; a circle at a member end = released moment. The selected member shows its local axes x, y, z.

Result modes are available after the calculation.

1 — Geometry (nodes)

#X [m]Y [m]Z [m]✕
1
2
3
4

Show explanation

Coordinates in metres; decimal comma or point. The Z axis points up.

2 — Members

Member 1: node 1 → node 2, L = 3.000 m

GPa
GPa
mm²
mm⁴
mm⁴
mm⁴
Moment releases at the ends
MtMyMzend iend j

Member 2: node 2 → node 3, L = 3.000 m

GPa
GPa
mm²
mm⁴
mm⁴
mm⁴
Moment releases at the ends
MtMyMzend iend j

Member 3: node 3 → node 4, L = 2.000 m

GPa
GPa
mm²
mm⁴
mm⁴
mm⁴
Moment releases at the ends
MtMyMzend iend j

Show explanation

β rotates the local axes y, z about the member axis. With β = 0° the y axis is horizontal and the z axis has a positive vertical component (for a vertical member z = +X). For a frame in the YZ plane set β = 90° for the columns.

Large numbers can be entered with an exponent, e.g. 8.356e7. The section y-y axis is horizontal at β = 0°.

A release is a hinge at the member end: the member does not transfer the selected moment into the node.

3 — Supports

Node 1
Node 2
Node 3
Node 4
Show explanation

Pinned blocks the translations ux, uy, uz; fixed blocks all six components. The checkboxes can only be changed with Custom (checked = blocked).

4 — Loads

L1

Show explanation

Positive values act in the positive global axis directions; gravity = negative value in the Z direction.

A uniform load acts over the full member length and is given per unit member length (not per projection).

5 — Calculation

The input is complete.

Results ↑ View

Results appear after pressing Calculate.

  • Members are straight, prismatic and linear elastic, modelled as spatial Euler–Bernoulli beams with uniform (Saint-Venant) torsion. A model has at most 10 nodes, 5 members and 20 loads in a single load case.
  • The global system is right-handed with the Z axis pointing up. The local x axis of a member points from node i to node j; at β = 0° the local y axis is horizontal and the z axis has a positive vertical component (for a horizontal member it points straight up), for a vertical member z = +X. The angle β (0° or 90°) rotates the cross-section about the member axis.
  • Moment releases Mt, My and Mz are set independently at each member end. A load is a nodal force or moment, a point force on a member or a uniform load over the full member length (per unit member length) in the direction of the global X, Y or Z axis.
  • A positive axial force N is tension, a positive moment My means tension on the −z side and a positive Mz tension on the +y side. Reactions are the forces and moments that the support exerts on the structure, as vectors in the global axes.
  • Results are shown only if the calculation passes the equilibrium and compatibility checks; any change to the model hides the previous results. A mechanism or a nearly singular system is rejected; a member free to rotate about its own axis (e.g. a member between two pinned supports) is only flagged with a warning.
  • The calculator does not consider self-weight, warping torsion, shear deformations, shear centre eccentricity, elastic supports, prescribed displacements or thermal loads.
  • The calculator performs first-order linear static analysis of a single load case. It does not cover load combinations, structural stability or cross-section checks and does not replace a comprehensive structural assessment.